5 thoughts on “How to clean the glue with glue on the ring, how to clean it”

  1. Tommie

    1. Soak hot water: When you find that 502 glue is made, soak it with hot water immediately, it takes about 5-10 minutes. Rub the glue on your hand back and forth slightly. Remove.
    2, dripping wind oil essence: Just prepare a bottle of wind oil essence, drip the wind oil essence to gently rub the finger glue and rub it a few times, it is also easy to separate the fingers.
    3, soap and water soaking: If your fingers are stuck by 502 glue, do not open your fingers hard, soak your fingers in a warm soapy water and then slowly open your fingers.
    Extension information:
    502 Increases:
    1, 502 have irritating, volatile, volatile smell and weak tears, which will stimulate mucous membranes and eyes, so protect the eyes.
    2. Avoid contact with the skin and enter the eyes. If you accidentally enter your eyes, wash and send it to the doctor immediately with a lot of water.
    3, open the metal pipe port with the tip of the rubber cover. Pay attention to the drilling pipe, do not pull the face, do not pull or squeeze the tube excessively.
    4, should first remove the binding surface oil, water, rust, paint, etc., the binding surface should be mild. 502 belongs to fast dry glue. Clean the adhesive surface before use. Put the bonding point before applying the glue, then keep it for a few minutes, and then let the glue slightly dry and let go. If you use it in large quantities, you should use good ventilation rooms and try to avoid contact with the skin.
    5. Just squeeze out a small amount of 502 glue on the side of the binding surface when used, press the other side to stick on the other side, and stick it in about 25 seconds.
    Reference materials Source: Baidu Encyclopedia-Ring
    Reference materials Source: Baidu Encyclopedia-502 glue n

  2. Diana

    The first, apply it directly with a wet towel, it will soften after a period of time, and then wash it off.

    The second type, using the same 502 to melt in a place with 502 glue stains, and remove it after softening.
    The third type, using insulating oil, the insulating oil is very good, 502 glue can quickly soften, and then wash it off directly
    The fourth type, use acetone The acetone has a certain toxicity, which will cause great stimulation to the eyes. If you accidentally enter the eyes, immediately wash with a lot of water. You can use sodium diluted sodium bicarbonate solution when cleaning.
    The fifth type, soak it with hot water, just soak for 5-10 minutes.

  3. Sophia

    502 Clear of glue:
    1. You can use a wet hot towel to stick to 502. After ten minutes, the solidified 502 will soften and it can be cleared. In addition, a drop of 502 can be dripped in a place with 502, and the solid 502 will also soften, so that it can be removed with a towel.
    2. Drop 502 in the original place to melt the original 502, and then quickly wash it off with water.
    3. Use insulating oil. The insulating oil in the inverted transformer is on the table. 502 glue quickly softened and can be rubbed quickly.
    4. The acetone solution can be washed.
    5, 502 glue is an instant glue. As long as it is dissolved with organic solvents, such as gyanone. However, inhalation is poisonous, pay attention to the use method, you can stuff the sticky part into the bottle.
    6. Small area sticks to 502 glue. Just soak it with hot water. If you apply 502 glue in a large area, apply acetone, and wait for about 5 to 10 minutes.

  4. Priscilla

    502 is a crispy glue, which can be vibrated to separate the sticky object; at the same time, 502 glue is not suitable for use under water content, so it is afraid of water. If the time requirements are tight, you can use organic solvent bubbles (be careful not to react with the adhesive body). This method can dissolve 502 glue in the fastest way to achieve the purpose of separating objects.

    Organic solvents:

    lytone, Yasitong, mek, Tian Na water dissolved, not at home, wash with gasoline or diesel, or wash it with some vinegar and then wash it. Also! (Banana Water "(commonly known as" Tian Na Shui "is often used as a diluing agent for fast paint).

Leave a Comment