stainless steel jewelry tag bulk wholesale How to design diamond rough to finished products?

21k gold jewelry wholesale I believe everyone knows that there are many diamond cuts, and many friends think that the more diamond cutting surface, the better. But just emphasize the scientific nature of cutting surface without considering the cutting method, it is also impossible to obtain bright diamonds. Cut the good or bad, rely on good polishing and cut in accurate geometry. In addition, there is also a need to emphasize that the amount of diamond surface rely on the size of the diamond, so diamonds contain certain principles in the design of the cut surface of the finished product. Let me see what the principles are with you.
Generally speaking, there are four main design principles of diamonds, which are the principles of cleanliness, the principles of care, the principle of marketing, and the principle of provincial work. These four principles are also international practice in the industry. Through the above principles, and from the specific situation of each rough stone, determine the grinding and cargo that should be adopted for each rough.
① Principles of care: The purpose is to increase the utilization rate of rough stones. It is necessary to ensure the least raw material loss in the process of this process, but also to make the next process from being affected. The best success rate is the principle of cost. But at the same time, pay attention to the clarity and cutting, take one -sided care, ignore the clarity and cutting work, which often reduces its overall value.
② Provincial labor principles: Diamond processing has always been said to labor -intensive industries. From rough to finished products, labor consumption is extraordinary. Under the premise of taking care, purity, and marketing, properly taking into account the principle of provincial labor is also a measure to improve economic benefits. For example, when a diamond rough can achieve the expected effect with both sawing and splitting, you should first consider using the split processing process, because the effect of split diamonds is higher than the saw diamond, which can save working hours.
③The principle of marketing: What grinding and carving types of diamonds are designed. How to choose between care and purity of cleanliness must be based on their own objective reality to make the product market -to -road and speed up the turnover of funds.
④ The principle of cleanliness: Diamonds are natural minerals, and there are very few real purity. The designer should take out a practical solution to remove the defects during processing. For example, the graphite bag is designed to be close to the juvenile surface and split surface to remove them during the grinding process. Or the design of the defect is designed in a place where it is not very conspicuous and does not occur, and the impact of defects on the clarity level is minimized. The designer must take care of the consumption and cleanliness, and repeatedly weigh the economic benefits as the scale to make favorable choices.
Then the abrasion and cargo of diamonds according to the principle described above, and then design the diamond marking line. It is generally divided into a diamond marking line, a saw diamond marking line, and a forming diamond marking line.
1. Drilling the marked line: The direction of the drill must be in the direction of the noodles, that is, the direction of the octopus crystal surface. In principle, contact with dual crystal requires the knife from the binocar combination. When the line is marked, the split surface can be marked for so that the opening point uses ink group to indicate that the point is on the crystal edge.
2. Saw diamond marking line: There are two options when sawing drilling. One is to see along the direction of the cube crystal surface, and the other is to see it along the direction of the twelve -sided crystal surface. The most common thing is to see along the direction of the cube crystal surface, because the occurrence rate of the occlusion of the twelve -sided crystal surface is often unsatisfactory. not open. After the thread is defined, the opening point is also marked with the ink group.
3. Setting diamond marking line: The forming diamond does not need to be split and saw, and one is made of one, so it is also called a granular diamond. Generally, only the low position is marked in the ink group, and there are also "forks" (x) in the middle of the circle. When encountering the rough stone that wants to "open the window" for observation, the designer is also the part of the window opening with ink groups.
It through the above content, you can know that the cutting surface of the diamond is just a indicator for judging the quality of the diamond. The value determined by the ultimate quality of the diamond is determined by the diamond 4C standard, rather than the number of diamond cut surfaces unilaterally. Let's judge. At the same time, the jewelry dealers and craftsmen will choose the most suitable cut and cut surface according to the shape and quality of diamonds to reduce unnecessary waste. So we only need to buy diamond jewelry of the heart!

unique wholesale jewelry louisiana First of all, you need to design a favorite pattern, cut the rough stones, and then embed the cut diamonds into the made accessories.